How To Install Colorbond Fence On A Retaining Wall

How To Install Colorbond Fence On A Retaining Wall. For the retaining wall, i’m planning to put it against the colorbond rear boundary fencing but unsure how far to extend it out. They are also used as a soil retention method, accommodating soil height variations of up to 600 millimetres.

Retaining Walls Perth WA Concrete Sleepers, Retaining from www.teamworkfencing.com.au

I'm going to erect a colorbond fence. Align and install the posts. It is more suited when the difference in levels is between 150mm and 250mm and fits between the colorbond posts which makes it a good option where there are objects that are too close to the fence line to allow post and panel or limestone retaining.

Source: www.pinterest.com

Rock 400mm 1 bag per hole (20kg bag) clay/firm earth 600mm 2 bags per hole (20kg bags) sand/loose fill 900mm 3 bags per hole (20kg bags) the preferred method of cutting sheets is to use a nibbler or tin snips. My retaining wall goes to about 1000mm above ground level.

Source: www.perthtradecentre.com.au

The most commonly used retaining walls in western australia are plinth, panel & post and limestone blocks. Do the same to the other end of fence.

Source: www.truelocal.com.au

Ensure that your pvc pipes are properly installed within your wall blocks since they will act as a support for your fence post. Do the same to the other end of fence.

Source: www.teamworkfencing.com.au

They are also used as a soil retention method, accommodating soil height variations of up to 600 millimetres. Colorbond fences have been tested to withstand worse weather condition.

Source: rapidconstructionsqld.com.au

I am planning to use concrete sleepers with the posts held in place with concrete. Rock 400mm 1 bag per hole (20kg bag) clay/firm earth 600mm 2 bags per hole (20kg bags) sand/loose fill 900mm 3 bags per hole (20kg bags) the preferred method of cutting sheets is to use a nibbler or tin snips.

Source: jarrahjungle.blogspot.com

Do the same to the other end of fence. Align and install the posts.

Source: jarrahjungle.blogspot.com

Set the ground pegs about 500mm at each end of the retaining wall and then connect. Then you would have to weld or mechanically fix a matching base plate ontop of the retaining wall posts, then bolt them together.

Source: www.houzz.com

Colorbond type fencing is becoming popular due to its long life compared with traditional timber fencing. With a sharpie, mark on the inside of each colorbond post the position of your bottom rail which will correlate to the height of your fence and the height of your retaining wall (i.e for 600mm high retaining wall, mark 600mm below your bottom rail mark).

Source: www.perthtradecentre.com.au

Other retaining options that can be considered are the steel plinth which is used when installing colorbond. However, your wall will need steel reinforcing and footing ties to meet strength requirements and as your fence adds a wind load to the wall as well it will have to have engineering approval, which you will need for walls over 0.5m anyway, but you must let the engineer know about the fence on top as it changes the forces involved.

An engineered retaining wall is designed for certain loads, ie retaining excavated or built up earthworks.

Installing the infill sheets for a colorbond fence is relatively easy but you will need someone to help you. Tue oct 28, 2014 3:59 pm. Colorbond fences have been tested to withstand worse weather condition.

Back filling might also help to install the fence so you wont need a ladder later on in the process.

Attach a fence directly to the top of your uprite retaining wall. Once you have everything else in order, it’s then time to dig the post holes so you can fit in the colorbond steel retaining wall posts. Then you would have to weld or mechanically fix a matching base plate ontop of the retaining wall posts, then bolt them together.

If you are installing a colorbond fence on top of a retaining wall, there are a few different options to choose from.

If it is then you can use an extension system to add a post. When constructed, a timber sleeper is often installed at the bottom of the fence for a. It comes in great colours, is easy to install and, for its expected lifespan, it is economical too.

Set the ground pegs about 500mm at each end of the retaining wall and then connect.

Uprite fence bracket is attached directly to the top of your sleeper wall post, the bracket simply bolts to the steel post through the two pre drilled holes in both. I want the fence to be higher than the fence posts will allow, so i want to fix it against a retaining wall. I'll add ag drainage behind the retaining wall also and connect it to the stormwater drain.

Installing fences can be done in three different ways.

Place post assembly in the hole, with the top 1850mm above ground and fill the hole with concrete. Colorbond® plinths fill the space between the bottom of your fence and the ground. Once the plate is welded and level, go ahead and put the rest of the sleepers into place, and fit them nice and tight.